Welcome to the LX Forum - Dodge Charger | Dodge Challenger | Dodge Magnum | Chrysler 300 Forum.
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

<<<<<< Register to remove these ads >>>>>>


Go Back   LX Forum - Dodge Charger | Dodge Challenger | Dodge Magnum | Chrysler 300 Forum > LX Forum - Preferred Vendors > Danko Reproduction


Reply
 
Thread Tools Display Modes
Old 01-01-2011, 09:56 PM   #1
MoPower
Preferred Vendor
 
Join Date: Mar 2010
Location: Miami
Name: Mo
Age: 57
Posts: 88

Car Model: Briliant Black Charger R/T
Year: 2007
Engine: 5.7L Hemi
Exclamation Danko Custom Rear Diffuser Installation Thread!!!!!!!!!!!
OK all my Charger buddies, here is the installation process of the Charger Diffuser, which is simple as pie! Removal of the rear bumper cover is pretty easy and will be covered in another thread.

1) First, hang the rear bumper cover (fascia) on something like a saw horse that lets the bumper be in it's natural shape. I have a special stand for such things...The blue line on the bumper shows where the edge of the diffuser goes.


2) Next, hold the diffuser in place and then put a strip of 2" masking tape just inside the edge where the studs go.

3) Make sure the 9 studs are not screwed into the back of the diffuser. Notice that the stud mounts are protruding just enough to make an imprint on the masking tape.

4) Next, tape the diffuser exactly in the place it belongs. This is an important step, so take your time and make sure it looks good from all angles.

5) Now you have to push hard above every stud to make a good imprint in the tape.

6) Remove the diffuser. If you don't have 9 legible imprints, do it again. Mine were clear the first time.

7) Next, I used a sharpie to highlight the spots to drill out.

8) With a 5/16" drill and bit, carefully drill the 9 holes.


9) Finally, install all 9 of the threaded studs into the mounts. You should use loc-tite on the threads to make sure they don't vibrate loose.

Last edited by MoPower; 01-01-2011 at 10:42 PM.
MoPower is offline   Reply With Quote
Old 01-01-2011, 09:56 PM   #2
MoPower
Preferred Vendor
 
Join Date: Mar 2010
Location: Miami
Name: Mo
Age: 57
Posts: 88

Car Model: Briliant Black Charger R/T
Year: 2007
Engine: 5.7L Hemi
Default
10) Now we are ready to install the diffuser! Turn the bumper over and remove the 6 pop nuts that hole the plastic brace in place. I used a screw driver to get it up, and then a pair of tin snips to grab and pull them out. remove the brace and flip the bumper over again.

11) You now need to bolt up the 9 mounts. You should know that the 2 end studs have a tendancy to be at a slight angle, so ovaling out the holes with the drill bit may be helpful.

12) Flip the diffuser over to check how it looks. At this point, you may need to remove it and do some slight trimming of the edge if it is hitting and not letting it seat properly, but usually it should be pretty close from the factory and not need much if any trimming.

13) The next step is to make sure the brace will go back in with no interfererce. I was real happy to see on mine that only very slight work was needed to clear the nuts but every diffuser will be slightly different so these details may vary slightly from one to another. On mine, the 3rd and 7th nut needed the little bar chopped out, and the 1st and 9th end nuts needed a hole drilled out to clear the nut. Notice the bar I chopped out on both sides with tin snips.


14) For the end nuts, I marked the circle to cut out with a white grease pencil.

15) The next 2 pictures show the process of opening up the clearance holes. If you don't have a hole saw, just drill lots of holes close together and then cut it out with tin snips.


16) Now we will install the last 5 nuts and bolts. You should see the 5 spots to drill scratched into the bottom of the part. One in the middle and 2 beside each exhaust port. Use a 5/16" drill bit . Make sure the diffuser is all the way in the correct position before drilling. Install and tighten each bolt before goint on to the next one.


17) Re-install the plastic brace with the pop nuts and hang the bumper back on your car. It should look something like this:




18) The next step will be to take it all off and get it painted, and install the mesh with some epoxy repair putty. Also, there is a foam rubber black gasket the you can install when you are ready for the final installation. More pics will be coming soon when I get them done, so stay tuned !!
MoPower is offline   Reply With Quote
Old 01-01-2011, 11:34 PM   #3
 
plmcrzy07's Avatar
plmcrzy07
Member
 
Join Date: Oct 2010
Location: Mass
Name: Dan
Age: 41
Posts: 99

Car Model: Dodge Charger R/T Daytona
Year: 2007
Engine: 5.7
Send a message via AIM to plmcrzy07
Default
That looks sick! I think we will see this diffuser in Jimmy's future...


__________________
plmcrzy07 is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump