Welcome to the LX Forum - Dodge Charger | Dodge Challenger | Dodge Magnum | Chrysler 300 Forum.
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

<<<<<< Register to remove these ads >>>>>>


Go Back   LX Forum - Dodge Charger | Dodge Challenger | Dodge Magnum | Chrysler 300 Forum > LX Forum - Preferred Vendors > Danko Reproduction


Reply
 
Thread Tools Display Modes
Old 02-12-2012, 12:57 AM   #1
MoPower
Preferred Vendor
 
Join Date: Mar 2010
Location: Miami
Name: Mo
Age: 57
Posts: 88

Car Model: Briliant Black Charger R/T
Year: 2007
Engine: 5.7L Hemi
Exclamation DANKO 3.5L V6 SHAKER HOOD KIT finally in the works!!!
After many years of promising that ONE DAY... I would come out with a V6 shaker, I'm finally gonna make good on my promise. What you see here is a local costomer's SXT 3.5L V6 Magnum. We are custom installing the shaker on his car and in the mean time, we will be making some new shaker base moulds so we can offer this same product to the masses. It will have a FULL sealed system, but it will be internally mounted, so the air box will be completely discarded. Anybody who is interested in this product, please let me know and I'll get your name on the list!! This should be available VERY soon as I have a hard deadline to get this done quickly and he needs his car back. Enjoy the pics!!
MoPower is offline   Reply With Quote
Old 02-12-2012, 12:57 AM   #2
MoPower
Preferred Vendor
 
Join Date: Mar 2010
Location: Miami
Name: Mo
Age: 57
Posts: 88

Car Model: Briliant Black Charger R/T
Year: 2007
Engine: 5.7L Hemi
Default
Before I can design the shaker pieces under the hood,I need a shaker hood with a hole in it so I might as well get this out of the way.
People always seem nervous about this step and I always tell them, this is the easiest part of the job and if you are gonna take it to the body shop to have this done, do yourself a favor and cut the hole first yourself to save money as the body shop overcharges for this since it appears difficult...You are now gonna see just how easy it is to do one of these shaker hoods. This is my fifth one. First you take off the hood

Then I put lots of tape on the hood to protect the paint and centered the pattern on the hood...pretty easy so far.

Next step would be to draw a dark line where to cut with a pen and then put another layer of 2" masking tape over the hood and retrace the cut line (you can see the dark line under the tape)

Here goes the first hole! no too hard to do!

And finally, I just cut out the hole with my cheapy jig saw and a 4 1/2" blade. I'd recommend a longer blade if you can find one, but this one barely was long enough and it worked pretty well. Tilting the blade about 15 degrees like you see here is REAL important, the hole on the bottom of the hood is basically larger than the hole on the top so the hood brace will go on easily.


Now, to find out how I did... the only damage to the paint was in the front on the hood ridges that stick up. Good thing that the chips in the paint are well within my 2" zone that will be completely covered up with the trim ring...

The hood brace is pre grinded and actually went all the way down and just dropped right in with not even any work to clean up the hole. and there was no side to side movement and no question exactly where it goes!!! A few minutes of screwing the 16 self tapping screws in the marked locations and we are just about done!

Next I put the insulation back in place and marked it about 1/2" inboard of the hood brace and got my big sissors and chopped out the center.

In go the 2 insulation pieces with the factory plastic retainers and we are done on the bottom!!

For now, I just temporarily stuck the trim ring on with double sided tape. Once it gets painted, I will install it properly with 3M tape and some adhesive underneath. It's a perfect fit as unsual and sits right onto the hood brace flange.

Now to get the hood back on!


Notice the Holley High performance air filter peeking through the scoops. this is what we will use on the inside so the factory airbox will not be needed.


Stay tuned for some more updates as I fly through this project. Got plenty of projects going on right now so I got to get this one done quick and get his
MoPower is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump